Groove Mixer features, the purchase and maintenance of knowledge
Characteristics of the channel mixer
  Channel mixer for mixing powder or wet materials, the different proportions of excipients mixed, dry powder blend is widely used in pharmaceutical, food, chemical, electronics and other industries. Channel mixer with material contact points are made of stainless steel blades and barrels are a small gap, mixed dead ends, stirring shaft at both ends has a sealing device to prevent the material outside diarrhea, hopper button to move the control, easy discharge particularly applicable to the uniform requirements, the proportion of poor materials, large material mixed.
  The main channel mixer features:
  Channel mixer has a compact, simple to operate, beautiful appearance, small footprint, clean, good mixing effect. The mixer unit by mechanical rotation, the S-type impeller rotation, and promote material back and forth turning, mixing, electrical control operation, the mixing time can be set to automatically shut down, thereby increasing the mixed quality of each batch of material.
  Select a six channel mixer Note:
  A. Works according to the spiral belt mixer for mixing the mixed double helix with the ability to push the material in the opposite direction should be basically the same. Within the spiral with the pitch should be less than the outer spiral bands, to achieve the ability to push material consistent inner spiral with the pitch should be less than the outer spiral bands, the width should be larger than the outer spiral band, otherwise it would be material in one direction concentrated. Therefore, in the choice of channel mixer to pay attention to this point.
  Two. The gap between the design principles, channel mixer, spiral band and the shell can be 4 mm to 10 mm, the material can be mixed friction driven by all participants. However, due to the friction coefficient is not the same granularity and materials, make the various components of the materials to participate in mixing time is not the same, resulting in the heterogeneity of the product. Some manufacturers have been aware of this and the product has been improved. Attention to the machining accuracy, the end of the gap reduced to 1 mm to 2 mm; another spiral belt between the spindle and the shell made of a position adjustable, can be regularly adjusted according to the amount of wear between the shell the gap. Select the channel mixer, the product of these two forms is the best option.
  3. Use the channel mixer to pay attention to the order of feeding. Generally vote aniseed, jade, rice flour, soybean powder, and then cast the group sub-material, such as premix. Note premix must not spiral elevator feeding the application of one-off tipping bucket feeding or artificial feeding, to avoid the segregation of the active ingredient in the premix loss.
  4. Select the channel mixer to pay attention to a material way. Should choose the form of a large door, do not choose the side of the mouth or small opening at the bottom of the material in the form. The reason is: mixer mixing completed in a specified time, the shortest possible time once put clear to ensure material uniformity; such as opening side of the mouth or bottom of the spiral band gradually put the net, one delay time, up less than expected productivity, material already achieve the best uniformity, excessive mixing but will make the material segregation and undermine the uniformity, and thus lose the significance of selected channel mixer.
  5 Use the channel mixer, should start in the mixer and then batch by batch feeding. Mixed end to the discharge and do not stop out of the net material and then mixed batch. If the full load and then start, will cause the power away from too much and burning motor.
  6. According to the daily production of the selection of horizontal mixing machine. Due to the mixer each batch of material and processing time of about 6 minutes, with the materials and the feed time, processing time of each batch of material can be 10 minutes, one hour can be processed six batches of material. If you choose each batch processing capacity of 100 kg, channel mixer, then the process 600 kg per hour. The user can be selected according to their needs the channel mixer.
  In short, choose an applicable channel mixer and used properly, will significantly improve the quality of its ingredients, and will soon reflect the benign effect in the breeding process. If you can master with premix technology, but also greatly reduce the cost of feed, and thus improve the profits of farming.
  How to increase the life span of the channel mixer, and its basic operation is to have a good day-to-day maintenance practices.
  The channel mixer is mainly used for mixing powder or wet materials, the different proportions of excipients mixed dry powder blend is widely used in pharmaceutical, food, chemical, electronics and other industries. So how do you channel mixer routine maintenance, to know the machine a good maintenance can enhance their life, so that you can save a small fortune in expenses. So how do you groove mixer for maintenance? This is perhaps the most concerned.
  Groove Mixer maintenance:
  A regularly check parts, 1-2 times a month, check the item for the various activities of the worm, the worm, bearings, shaft seal part of the rotating flexible wear, found that the defects should be repaired in time, so that the groove mixer can be used normally.
  Lubrication: reducer lubrication with oil-immersed, its oil reserves must remain in the oil standard line, the oil must be kept clean. Such as frequently used to be every three months for a new oil replacement should reducer removable and washable cleaning, coupled with new oil.
  Groove Mixer electrical control parts, should be kept clean, sensitive, and found that the fault should be repaired in time.
  Once finished or laid off, you should remove the remaining material of the mixing tank, brush clear the machine part of the residual powder child. Such as disabled a long time, Groove Mixer all clean, and the tarpaulin cover.
  5, the mixing paddle assembly and disassembly should be light demolition, stabilization installed light, to avoid distortion damage.
  As long as usual to spend a small amount of time, can have unexpected results, you may wish to try.
Related News:
· Innovation, energy saving, environmental protectio  
· Vacuum dryer product performance characteristics a  
· Vacuum dryer used for inspection and debugging wor  
· Difficulties and reasons cannot start mixing machi  
· The correct operation method using vacuum dryer  
· Development advantages and characteristics of dome  
· The difference between the special vacuum dryer an  
· Detailed description of each component characteris  
· The dominant position in the whole vacuum dryer dr  
· Trough type mixer sometimes appear large area leak  
Related Products:
· PGL Spray Drying Granulator
· High speed mixer
· SET series double screw extrusion pelletizer
· VI forced mixer
· Mixing machine W series
· Powder machine ZSJ series vibrating screen
· FZ series of crushing granulator
· Chinese medicine grinder
· DWT series of drier for dehydrated vegetables
· Multi-layer belt dryer

Copyright 2013 Chang Zhou Zhizun Machinery Co.,Ltd All Rights Reserved.Design by Reach.
Tel:86.519-88906508 Fox:86.519-88902679 Add:Jiaoxi Changzhou Jiangsu Pro China P.C:213116