Shaker installation of rock particles
The main structure of the rock particles, the following five categories
  Body: body is an independent rectangular cylinder on the device closed bearing and powder bucket connection, pink bucket toward the body, under which is equipped with a V-shaped chassis, the ground a broad and flat, so be fitted with can be positioned anywhere indoor use.
  , Particle manufacturing equipment: rotating drum lying set the bucket in the powder below, front and rear bearing supports for the inverted rotary rack drive, the end of the bearing cap is movable assembly and disassembly, as long as the spin under a wing nut, the bearing cap and rotating drum to be pulled out, place the roller at both ends of the system has a convex side ring, embedded bearing indoor, that is not to make the oil penetrate the powder will and will not be bonded plugged.
  Gearbox: using a worm gear, the ratio to 1:12, the box can be stored oil to ensure good lubrication of gear and no noise, endoscopic observation, observation of the functioning of the oil reserves on the box, worm gear outer end, equipped with eccentric shaft to drive the rack for reciprocating movement.
  4, folder sieve tube: device on both sides of the rotary drum, steel pipe manufacturing, in the middle to open a long trough, both ends of the embedded slot of the screen, turn the flower-shaped hand wheel will screen wrapped in a cylindrical rotating drum hand wheel, gear shore, tightness can be adjusted.
  5, the motor frame: a screw bolt firmly, the motor mounted on the iron, when the rotation of the screw bolt, the motor up and down movement for adjustment of belt.
  , Rock particles, machine vibration sieve installation and commissioning steps and shaker install debug Note
  1.1 rock particles prior to installation, the first reference to the packing list to check parts are complete and damage.
  1.2 refer to the installation diagram for installation, chassis which support must be horizontally mounted on the foundation, the basis should have sufficient stiffness and strength to support all the dynamic load and static load of the shaker.
  1.3 can make use of the screen box trunnion lifting screen, not directly linked to the exciter on the lifting of the entire sieve.
  1.4 Installation of the rock particles, machine screen, make sure to kept to a minimum 75mm gap between the screen box and hopper, trough a class of non-moving parts.
  1.5 rock particles after installation, around the screen surface level, otherwise, the spring seat and bearing pad of thin iron plates to be adjusted.
  1.6 The spring must be in a vertical state, the spring fixator in the ear axis of the screen box.
  1.7 shaker drive direction as, standing on the feed side, the face of the material flow direction, and observe the motor position, the left hand side to left to drive, right hand side for the right to drive. The shaker symmetrical design, both sides pulley. Replace the motor position to drive the direction of change around.
  1.8 to ensure that the V-belt tension the full amount of the adjustment of the two pulley face is adjusted in a plane.
  1.9 test before hand (or other method) rotating exciter. Flexible rotation, no jamming phenomenon, before starting the machine.
  1.10 rock particles, install the adjustment is completed, should be not less than two hours of no-load commissioning requirements of the smooth operation, no abnormal noise bearing maximum temperature does not exceed 75 ℃.
  1.11 according to the site usage through appropriate changes in the number of eccentric block to adjust the amplitude of the size of, in order to achieve the desired screening effect
Related News:
· Innovation, energy saving, environmental protectio  
· Vacuum dryer product performance characteristics a  
· Vacuum dryer used for inspection and debugging wor  
· Difficulties and reasons cannot start mixing machi  
· The correct operation method using vacuum dryer  
· Development advantages and characteristics of dome  
· The difference between the special vacuum dryer an  
· Detailed description of each component characteris  
· The dominant position in the whole vacuum dryer dr  
· Trough type mixer sometimes appear large area leak  
Related Products:
· PGL Spray Drying Granulator
· High speed mixer
· SET series double screw extrusion pelletizer
· VI forced mixer
· Mixing machine W series
· Powder machine ZSJ series vibrating screen
· FZ series of crushing granulator
· Chinese medicine grinder
· DWT series of drier for dehydrated vegetables
· Multi-layer belt dryer

Copyright 2013 Chang Zhou Zhizun Machinery Co.,Ltd All Rights Reserved.Design by Reach.
Tel:86.519-88906508 Fox:86.519-88902679 Add:Jiaoxi Changzhou Jiangsu Pro China P.C:213116