The universal grinder generally use motor directly connected to smash device
   Universal grinder are hopper bucket outside of the following feed regulation flapper should adjust the flapper to the blanking size, according to the degree of friability of the material and the grinding fineness, indeed when the position and tighten .
  The universal grinder beneath the discharge port, if the discharge of the amount of material wind caused slightly spray material phenomenon, should be in a material bag plus port bundling material by Higuchi bag slowly spillover.
  Should be carried out before the first boot once empty running test, commissioning should be preceded by checking the universal grinder sites to verify that the aircraft is qualified.
  Universal grinder has a water-cooled, plus use should be used to avoid damage to the bearings.
  The universal grinder installation and debugging
  The universal grinder fixed the chainring Imperial, Imperial go bolt can.
  2 fold the Royal universal grinder bearings, first open cavity, the Royal derotation chainring or rotary knife, take away the maze and the center bearing cap, then Imperial to the outer end of the pulley and bearing cap, which launched both ends of the axial Imperial go to both ends of the bearing and shaft.
  Installation still keep the alignment of the the shaft cavity bush hole oil eye.
  4. Installation screen, sieve the circle close to the machine cavity shoulder tank, otherwise damage sieve circle when the door is closed.
  5 making sieve laps, mesh expand the length should be noted in the sieve circle shoulder sized screen damage manufacturers should be equipped to do.
  6 Install the screen: the two sieve Circle merged alignment mark and then sieve into within the sieve circle, such as the mesh too tight, the screen inward curved into, and then can be pushed outward.
  The universal grinder commonly used motor directly coupled crushing device, this connection is simple, easy maintenance. However, if both in the assembly process is not well connected, it will cause the overall vibration.
  (1) of the rotor and the rotor different heart. Left and right movement motor position, or in the motor bottom underfoot padded to adjust the concentricity of the two rotor.
  (2) rotor different heart. The reason is branched palm of the rotor shaft 2 supporting surface is not on the same plane. The underside of the support bearing pad copper, or in increased bearing bottom adjustable wedge two axis head concentric. Double Roll Crusher.
  (3) grinding chamber parts vibration. The reason is the uneven quality of the coupling with the rotor join different heart or rotor inside the flat hammer. Can be taken according to the different types of coupling method withered the whole coupling with motor coupling: when the uneven quality of the hammer, to be re-matching each set of hammer, hammer symmetrical, symmetrical hammer chip error is less than 5G.
  (4) the original balance is destroyed. Motor repair, dynamic balancing test to be done to ensure that the whole match balanced.
  (5) of the anchor bolt is loose or Without a solid foundation, installation or maintenance, evenly tighten the anchor bolts, foot between the foundation and grinder to see the video of the entrepreneurial story. To replace the damping device to reduce vibration.
  (6) the hammer to break or smash indoor hard debris. These will cause rotation of the rotor imbalance, caused by machine vibration. Therefore, periodically check for wear hammer. Replacement to be symmetrical replacement; the grinder operation of not a normal voice, to immediately stop check and find out the reasons timely.
  (7) the universal grinder System connected with other devices do not coincide. Such as feeding tubes, the discharge tube joins improper, will be to cause vibration shipped and made sound. Therefore, these coupling section should not be used hard links, the best soft join.
Related News:
· Innovation, energy saving, environmental protectio  
· Vacuum dryer product performance characteristics a  
· Vacuum dryer used for inspection and debugging wor  
· Difficulties and reasons cannot start mixing machi  
· The correct operation method using vacuum dryer  
· Development advantages and characteristics of dome  
· The difference between the special vacuum dryer an  
· Detailed description of each component characteris  
· The dominant position in the whole vacuum dryer dr  
· Trough type mixer sometimes appear large area leak  
Related Products:
· PGL Spray Drying Granulator
· High speed mixer
· SET series double screw extrusion pelletizer
· VI forced mixer
· Mixing machine W series
· Powder machine ZSJ series vibrating screen
· FZ series of crushing granulator
· Chinese medicine grinder
· DWT series of drier for dehydrated vegetables
· Multi-layer belt dryer

Copyright 2013 Chang Zhou Zhizun Machinery Co.,Ltd All Rights Reserved.Design by Reach.
Tel:86.519-88906508 Fox:86.519-88902679 Add:Jiaoxi Changzhou Jiangsu Pro China P.C:213116